Sökresultat

The behavior of Ethanol and seven fuels in the boiling point range of gasoline but with an Octane Number spanning from 69 to 99 was investigated in Partially Premixed Combustion. A load sweep was performed from 5 to 18 bar gross IMEP at 1300 rpm. The engine used in the experiments was a single cylinder Scania D12. To allow high load operations and achieve sufficient mixing, the compression ratio w

It is tractable to increase the torque for an HCCI engine and one way is to add a turbocharger. Operating in HCCI mode requires accurate control of the combustion phasing, CA50. The higher the engine torque, the narrower the CA50 window becomes where HCCI operation is maintained. As the CA50 varies stochastically between cycles this requires improved CA50 control for turbo HCCI engines. The main f

By using a turbo the operating range of the HCCI engine can be increased, but at the expense of increased controller complexity. The dynamics the turbo introduces in the intake and the exhaust manifolds, have a large impact on the in-cylinder mixture temperature, pressure and finally the combustion phasing. To compensate for this and to maintain desired combustion phasing, precise control of the n

For diesel engines the major exhaust problem is particulate matter and NOx emissions. To reduce NOx, exhaust gas recirculation (EGR) is often used. The behavior of the EGR-level will therefore influence the emissions and it is therefore valuable to keep track of the EGR-level. Especially during transients it is difficult to predict how the EGR-level varies. In this paper the CO2-level in the intak

Partially Premixed Combustion (PPC) is a combustion concept by which it is possible to get low smoke and NOx emissions simultaneously. PPC requires high EGR levels and injection timings sufficiently early or late to extend the ignition delay so that air and fuel mix extensively prior to combustion. This paper investigates the operating region of single injection diesel PPC in a multi cylinder heav

A diesel engine developed for an international market must be able to run on different fuels considering the diesel fuel qualities and the increasing selection of biofuels in the world. This leads to the question of how different fuels perform relative to a standard diesel fuel when not changing the hardware settings. In this study five fuels (Japanese diesel, MK3, EN590 with 10% RME, EN590 with 3

Natural gas and hydrogen enriched natural gas has been tested as fuels together with diesel oil and RME in a single cylinder Scania research engine. The gas was introduced as port injection while the diesel was introduced as early direct injection. Because the gas was premixed with air before combustion and the diesel was injected early in the compression stroke, the engine ran close to HCCI mode.

In HCCI you do not have the same control of the combustion like in SI and Diesel engines. Controlling the start of a combustion event is a difficult task and requires feedback from previous cycles. This feedback can be retrieved from ion current measurements. By applying a voltage over the spark gap, ions will lead a current and a signal that represents the combustion in the cylinder will be retri

Utilization of an ethanol driven, combustion-based power generator promises high-efficiency combustion in diesel-like engines and avoids problems connected to shrinking supplies of fossil fuels since fuels like ethanol or dimethyl ether can be produced from renewable resources. Fuel injection into such generator through a piezoelectric micro mass flow controller (MMFC) features low power consumpti

A piezoelectric micro mass flow controller (MMFC) for liquid fuel injection into a mini-HCCI-motor for power generation is introduced. Piezoelectric actuation ensures negligible power consumption for fuel injection allowing self-sustaining operation. A pressurized fuel tank is connected to the MMFC which is designed like a normally-closed, on-/off-operating valve. Integrated piezoresistors are use

This work has focused on studying the in-cylinder pressure fluctuations caused by rapid HCCI combustion and determine what they consist of. Inhomogeneous autoignition sets up pressure waves traversing the combustion chamber. These pressure waves induce high gas velocities which causes increased heat transfer to the walls or in worst case engine damage. In order to study the pressure fluctuations a

utomotive systems offer a rich opportunity for hybrid models, controls, and tools. Beyond the traditional use of hybrid models for representing the behavior of the composition of discrete controller and continuous plants, automotive mechanical systems exhibit hybrid behavior as demonstrated in this chapter. In addition, hybrid systems can be used to capture system specifications at the highest lev

Mid-infrared polarization spectroscopy was applied to detect HCl at trace level in an atmospheric pressure premixed H2/O2/Ar flame with chloroform seeding. Detection sensitivity and potential interference from water lines was investigated.

An estimation model which uses the gross heat release data and the fuel energy to estimate the total amount of emissions and unburned Hydro Carbon (HC) is developed. Gross heat release data is calculated from a self-tuned heat release method which uses in-cylinder pressure data for computing the energy released during combustion. The method takes all heat and mass losses into account. The method e

Phosphor thermometry, a remote temperature sensing technique, is widely implemented to measure the temperature of different combustion engines components. The presence of engine lubricant can influence the behavior of the applied sensor materials, known as thermographic phosphors, and thus leading to erroneous temperature measurements. The effect of two engine lubricants on decay times originating

This study investigates photomultiplier tube (PMT) nonlinearities, relevant for lifetime phosphor thermometry, at various decay times to assess and minimize the impact on temperature measurement accuracy. The focus is single-shot measurements performed in harsh environments where phosphor signal attenuation often is a concern. The sensitivity of decay time measurements to changing phosphorescence

Quantitative measurements of CH4 mole fractions at different HAB in the flame were realized by a calibration measurement in a low pressure gas flow of N2 with a small admixture of known amount of CH4. A comprehensive study of the collision effects on the IRPS signal was performed in order to quantify the flame measurement. The concentration and temperature measurements were found to agree reasonab